| Items |
 i3-12H1 I3-Industrial Standard Precipitators - 3 Ton Unit |
 i3-16H1 I3-Industrial Standard Precipitators - 4 Ton Unit |
 i3-20H1 I3-Industrial Standard Precipitators - 5 Ton Unit |
 i3-24H1 I3-Industrial Standard Precipitators - 6 Ton Unit |
 i3-30H1 I3-Industrial Standard Precipitators - 7 1/2 Ton Unit |
|||||
| Description |
Industrial Standard Precipitators - Model Series: i3 (In-Duct, Spray Wash) - 3 Ton through 8 Ton Units I-series: Like the Commercial (C-series), the industrial, in-duct designs use housing or cabinet structures to support the cells installed within them. The galvanized cabinet structure can be factory finished on it exterior in enamel at the customers option. Seal welding of the cabinet is also available at option and required for UL710 ductwork installations. Again, In-duct design means that the precipitator is supplied without an air handler and will be cut into a section of horizontal flow ductwork. Commercial cell designs are typically applied to applications where frequent and aggressive cleaning of the cells will not be required. |
|||||||||
| Air Flow Capacity | 34 m³/min1200 ft³/min | 45.3 m³/min1600 ft³/min | 56.6 m³/min2000 ft³/min | 68 m³/min2400 ft³/min | 85 m³/min3000 ft³/min | |||||
| Rated Efficiency | 90 % | |||||||||
| Air Conditioner Capacity | 3 tons | 4 tons | 5 tons | 6 tons | 7 1/2 tons | |||||
| Air Flow Resistance (wg) | 0.1 in | |||||||||
| W - Width | 29 9/16 in | 36 3/16 in | 44 7/16 in | 51 5/16 in | 65 3/4 in | |||||
| X - Duct Opening | 23 1/16 in | 32 11/16 in | 40 15/16 in | 47 13/16 in | 62 1/4 in | |||||
| Y - Height | 23 in | |||||||||
| Z - Duct Height | 15 7/8 in | |||||||||
| Cell Removal Clearance | 27 in | 20 in | 25 in | 27 in | 25 in | |||||
| Approximate Shipping Weight | 140 lb | 175 lb | 200 lb | 225 lb | 250 lb | |||||
| Power Package Quantity | 1 | |||||||||
| Voltage | 115 V | |||||||||
| Frequency | 60 Hz | |||||||||
| Power (Per Pack) | 30 W | 40 W | 45 W | 50 W | 45 W | |||||
| Water Inlet | 3/4 in | |||||||||
| Drain Flange (Iron Pipe Size (IPS)) | 2 in | |||||||||
| Water Required at 40 Pound per Square Inch (PSI) Per Tier | 11 gpm | 14 gpm | 20 gpm | 22 gpm | 29 gpm | |||||
| Additional Information | The I-series has the same efficiency as the commercial or C-series, however it is sturdier. Due to its higher cost, some customers opt for the C-series over the I-series. In overview, the I-series cell uses twelve tie rod supports for the collector plates; its ionizing section is supported without ceramic insulators; and its end plates are made of heavy gage aluminum. Otherwise, the I-series cell has collector plates, spacers and an ionizing section that are identical with the materials and dimensions of the residential and industrial cell designs. | |||||||||
| Note | UAPC is committed to on-going improvement. Dimensions & specifications are subject to change without prior notification. | |||||||||
| Manufacturer | Universal Air & Gas | |||||||||
|
|
||||||||||
